Propress Connections: Metal tubes are connected with specialized ProPress connections. With a pressing tool, the connections create a water and air tight seal instead of the traditional method of soldering with a bonding agent. Viega was at the forefront of technology when it came to progressive accessories and should be your first port of call. Plumbing is something that professionals and do-it-yourselfers alike dread. Who knows what you’ll find if you tear down the old walls.
What is the process for using ProPress?
When it comes to traditional pipe fittings, there are three basic ways to install pipes and fittings. Threaded steel tubes are one technique. To connect two pieces of pipe or connectors, use a threaded design on both ends. Pipes come in various lengths and diameters and are often used to transport sewage and natural gas. This approach fails to handle unknown or unusual pipe runs.
How to join steel pipes at points?
An electric welder is used to join steel pipes at the points where they are joined. This method of installing conduit and fittings has been around for a long time, but new products like Progress fittings have entered the market and are touting their advantages over older methods.
Traditional methods:
Traditional methods use soldering or soldering to join copper or carbon steel tubes at connectors. Flux and heat are used to join copper tubes with fittings, then solder is applied to the connection for a lasting hold. Many steps of traditional methods have been eliminated due to the innovative design, saving a lot of time during the insulation process. Although they are more expensive than conventional accessories, their popularity and value in the field has only grown over time.
Other methods:
Depending on the material, the other two methods are soldering and soldering. To join different materials like copper, you use fittings that wrap around the pipe. After that, they assembled it using a soldering iron and heated components. Electric welders are used to join and seal steels that are more difficult to weld, such as carbon and stainless.
Streamlines the installation process:
ProPress, on the other hand, speeds up the installation process considerably. There is no need for soldering or soldering, and there is no need to wait for permits or take any exact measurements. By eliminating fire hazards, pipes do not even need to be emptied or cleaned before installation. Let’s compare the installation process for the Viega ProPress to that of a traditional copper fixture.
How does it differ from other similar products?
Most renovations require a significant amount of piping, whether for plumbing or gas. Using a device like the Viega ProPress is one option. Viega’s ProPress is a newer technology compared to other popular options. ProPress fittings use an innovative new method of crimping tubes instead of the more conventional approach.
O-ring retaining press tool:
The connection design incorporates an O-ring with rubber seals on both ends. Each end of the tube is slid into place and an O-ring retaining press tool is used to compress the surrounding area, creating an air and water tight seal. Due to its ease of use, reliability and the speed with which accessories can be attached, Viega’s progressive accessory technology has become very popular with contractors.
Replacing an accessory in a traditional copper installation:
Step 1: Close the valves that control the flow of water or gas.
Step 2: Drain completely or empty the line
Step 3: Remove the solder by heating the joint. If heating is not an option, destroy the accessory.
Step 4: Using a wire brush or other abrasive, remove all debris from the tube and fitting.
Step 5: There should not be any old welds as this can cause corrosion or lack of adhesion.
Step 6 The tube must be flushed after it has been cleaned. The solder adheres better to metal surfaces when this step is complete.
Step 7: Heat the tube with a torch. If you’re in a confined space, pay attention to what’s behind the flame. Apply solder to the joint once the line has reached the proper temperature.
Step 8: Allow the solder to cool completely before attempting any other work with it. When there is the slightest movement, the solder can crack and a leak can occur.
Step 9: Return the gas or water flow and check for leaks after the solder has hardened and cooled. If leaks are discovered, the process must be restarted to correct them.
Installing the Viega ProPress Copper: Replacing an accessory:
Step 1: Close the valves that control the flow of water or gas.
Step 2: To ensure your safety, turn off the gas and disconnect the line. It is not necessary to completely drain all water pipes.
Step 3: Discard the old accessory. Weld with a torch or remove the fitting if it is broken.
Step 4: Then install the new fitting over the old ones.
Step 5: Fix the accessories with a pressure tool.
Step 6: Check that the Smart Connect dot is properly pressed in. Instead, it would help if you used the press tool one more time before giving up.
Viega 78052 ProPress Zero Lead Copper:
- A consistent, strong, reliable and waterproof seal is achieved in four to seven seconds.
- With this feature, technicians can perform maintenance and repairs quickly by joining wet connections.
- Adaptable to any new or retrofitted commercial, industrial or residential project
- Requires no tanks, hoses, thread cutters, solder or flux to use
Viega 77387 ProPress Zero Lead Copper:
- In four to seven seconds, connections are made with a waterproof seal that is consistently strong and reliable.
- Installers can now connect wet fittings, making this the fastest maintenance and repair option available.
- As a result of the quick installation, maintenance and new construction are completed on time or even earlier.
- Ideal for new builds, renovations or retrofits in commercial, industrial or residential environments
- It does not require tanks, hoses, thread cutters, solder or flux to use.
How far apart are ProPress connections?
When used with Viega Progress accessories System and piping connections can be made in just 7 seconds, eliminating the need for burn permits and fire surveillance in the process. As awareness of this technique grows, so does the number of questions about its proper application. The Viega ProPress Systems Installation Manual provides a detailed answer to this critical question. Most of the time, the distance is determined by the diameter of the pipe being used. propress accessories, propress accessories propress accessories, propress accessories, propress accessories.
Also read: Use the strongest mid-back muscles using a backpack.